Thursday, September 26, 2019

Low density polyethylene Research Paper Example | Topics and Well Written Essays - 1250 words

Low density polyethylene - Research Paper Example In recent years, another dimension of environmental aspect has been added to reduce the global warming and related factors. (LDPE PERP 2010, p4) This paper deals with mainly the production processes of LDPE and its effect as life cycle assessment. Production Processes Installed capacities of LDPE based on production processes employed can be presented schematically as per the following diagram. Source: http://www.chemsystems.com/about/cs/news/items/PERP%200809_1_LDPE.cfm The technologies based on tubular and autoclaves reactors are used for the polymerization of ethylene. Polymerization process is carried out at high pressure between 1500 and 3000 bar and at temperature between 120 and 320 degree centigrade. A large variety of grades are produced using a single reactor line. Tubular Reaction Process The major outlines of the process can be described as per the following. Ethylene feedstock is compressed and mixed with the recycled ethylene and co monomer such as ethyl acrylate, vinyl acetate, or methacrylic acid. The mixture is then pressurized in the tubular reactor at certain pressure. Polymerization of the monomer takes place in the presence of organic peroxides. Reactor has several zones to increase the conversion rates. Per reactor pass conversion rate is found to be between 15 and 35 percent. The separation is done in two stages. The mixture of ethylene and polyethylene enters the high pressure separator and splits into an ethylene rich gas and polymer rich liquid. The polymer rich liquid at the bottom of the high pressure separator is taken out to the low pressure separator. The ethylene gas leaving the separator is sent back to the compressor and again mixed with fresh ethylene. The liquid stream is taken to the extruder for making the pellets of the polymer compound. (Pladis 2006) ExxonMobil has a long history of working with tubular reactors to manufacture LDPE. As claimed by ExxonMobil, tubular technology has a lower operating cost than autoclave tec hnology. Currently, 14 plants are in operation based on tubular technology as provided by ExxonMobil giving production output of 2500kta at different locations. (LDPE tubular†¦2010) Autoclave Process The compressed ethylene feedstock is mixed with comonomer such as ethyl acrylate, vinyl acetate, or methacrylic acid. Then the mixture is allowed to enter secondary compressor where it is compressed at very high pressure of 45,000 psi before entering autoclave reactor. Initiator accelerates the polymerization process. The molten polyethylene is taken out through separator and taken to extruder for making pellets and further processing. (Lyondellbasell 2010) A typical flow diagram of autoclave process for producing LDPE can be represented as per the following. Source: http://www.lyondellbasell.com/techlit/techlit/Tech%20Topics/Plant%20Profiles/Autoclave%20LDPE%20Technology.pdf Tubular versus Autoclave Reactor Processes Both, tubular and autoclave, are proven processes but there is s ome subtle difference in the product structure of resins produced from these processes. The difference lies in the level and type of long-chain branching. The autoclave process provides more long-chain branching compared to those provided by tubular reactor. That is due to higher level of backmixing possible in case of tubular reactor. In contrast, tubular reactor provides little backmixing as the reaction flow carries the polymer down the tube as reaction progresses; however, such subtle

Wednesday, September 25, 2019

African American Krumpin Culture Essay Example | Topics and Well Written Essays - 750 words

African American Krumpin Culture - Essay Example ountry, and their interaction with their white counterparts that one gets to appreciates the political, economic, cultural, and social realities of minority groups. This is as well as the their contribution in redefining America as it is today. The Krumpin in North Hollywood provides the opportunity for examining this history from the perspective and voices of the people who lived through it. In this regard, one can learn to evaluate and contextualize the first-hand accounts from the past and their contribution to the present and the future. To a great extent, the Krumpin in North Hollywood facilitates the examination of how race in general and blackness in particular, were created, lived, and evolved over time. During the 818 session, it is plausible that the presence of the local security machineries reminds one of the status of the parking lot as a private space. Hence the prohibition of any form of intrusion into it (Frazier, Robeson, & Koslow 2). While circling the perimeter of the parking lot, the local police, and other paid security personnel frequently command the dancers to lower the volume of their music or leave the area. Failure to this, the dancers risk being imprisoned. This is a clear demonstration of the curtailing of freedoms as witnessed during the repressive periods of the 1950s and the 1960s where the minority groups had much of their freedom limited through the use of state agencies. In fact, the practice of young people forming a gathering in an empty, though private yard, and the police encroaching on their activities elicit the general culture of domination and regulation. This is especially of the marginalised groups in the U. S. To some extent, it is noteworthy th e state is adamant in curtailing the use of public space, not just by the young blacks, but also by the brown youths. It seems that many forces are at play here with corporate takeovers of public space. The expansion of outdoor performance spaces that serve mainly the interests

Tuesday, September 24, 2019

Station Nightclub Fire Research Paper Example | Topics and Well Written Essays - 1250 words

Station Nightclub Fire - Research Paper Example Station night club has a by complex layout of the club and the bar section and has small entrances and exits. The complexity of the club’s architectural structures contributed to the loss of substantial lives during the fire incident in 2003. The fire incident happened during the time when the club’s management had scheduled a filming session concerning fire safety in clubs. This session was scheduled to conduct public lessons on fire issues after a crowd management issue that had claimed some lives at another club within the island. In the process of conducting the exercise, the club’s management allowed the use of pyrotechnic devises to demonstrate the practical aspects of the lesson. The pyrotechnic flames ended up igniting the flammable materials at the platform part of the club which eventually caused the spread of the fire the other sections of the club. The incident that led to the ignition of flames to the spread of fire inside the club took approximately 6 minutes. This short period instilled panic to the clubbers who in turn struggled to exit the building. Their efforts to move out of the club were hindered by the stampede that ensued at both the escape routes and the main entrance of the club. Few minutes after the fire, the whole club was covered in flames while the people were still struggling to free themselves. 10 minutes after the fire, the club’s fire management team and the fire rescue team initiated their efforts to put out the fire. However, their efforts to rescue the trapped club members were unsuccessful given the fact that the fire had reached its full blown stage. The aftermath of the incident was characterized by immediate review of the codes applied by the company in fire incidences. This process entailed reviewing of the codes by the NFPA and initiation of a research project to test the efficiencies of the codes that were in existence before the fire (Barry, 2010). Among the codes that were addressed after the fire

Monday, September 23, 2019

The ability to learn faster than your competition may be the only Essay

The ability to learn faster than your competition may be the only sustainable competitive advantage - Essay Example marking is an externally focused quality improvement technique that looks at the best practices of departments within the organisation, competitors and organisations with activities that are deemed to be functionally similar. As long as superior performance is identified the next step is to gain an understanding of the enablers or drivers of such performance and then apply them to the organisation (Swanson 2005, p. 243). Benchmarking is one of the strategies used in order to compete effectively in the market. It is a process that is used by organisations in order to target the key areas in their operations that can be used to improve competitiveness, productivity and quality. Organizations use benchmarking when they compare their performance against other companies doing similar business (Gitlow 2005, p.195). Quality needs to have a basis for comparison and so organisations use this strategy to determine how they are performing in comparison with their competitors. This allows them to remain competitive. Comparison is normally done with the best performing organisations. Every organisation can benefit from benchmarking as it is highly unlikely that an organisation does everything well or has nothing to learn from the successes of other organisations (Swanson 2005, p. 203). Benchmark is done as a structured process so as to improve performance and achieve improvements. Benchmarking simply put, is the practice of being humble enough to admit that someone else is better at doing something, and being wise enough to learn how to match and even surpass them at it (Williams 2004, p.226). Benchmarking as mentioned is done so as to set performance standards and so as to achieve superior performance that will result to having a competitive advantage in the industry (Peters 2007, p.89). The 2 basic types of benchmarking are internal and external. The internal aspect of it involves self analysis of a company’s own activities so as to determine its strength and

Sunday, September 22, 2019

Personal Statement Example | Topics and Well Written Essays - 500 words - 47

Personal Statement Example This was a trial for me on whether I could handle the PA career and most of all whether it was really what I wanted to do when I grew up. As a medical assistant, I got to perform services that a PA performs under direct supervision from the medical doctors I was working for and this got me really interested in this line of work. I had the opportunity to carry out what I had grown to love which was to help people and make them feel better as well as putting smiles on their faces even though they were physically unwell. I became a volunteer at the American Red Cross as well as at the Veteran’s Foundation after my job. This was propelled by the suffering I had witnessed in Iraq as well as it was another experience for me to be a PA. Being a volunteer meant I now had an opportunity to assist people through providing therapeutic and preventive services no matter how minimal an impact I made. The satisfaction from seeing the smile on people’s faces who had been suffering health wise before made me go to bed happy and satisfied which was a rare occurrence for me. My final journey towards making the decision and following my passion came when my mother had to undergo an open heart surgery. There was a team of physical assistants on the table with the doctor assisting him with everything and this sealed the deal for me. I was determined more than ever to join this career and fulfill my dreams and seeking admission into this program is the deal breaker. I would like to specialize and focus primarily on urgent care as I will be handling people without primary care physicians or those who are too scared to visit emergency rooms but they would still like remedies for their injuries or illnesses that are not too serious. This line of specialization is appealing because it is what I have learnt and gained experience on from volunteering at the Red Cross. Being granted this

Saturday, September 21, 2019

Advertisements That Make Women Look Bad Essay Example for Free

Advertisements That Make Women Look Bad Essay Some advertising companies do not see the problem with using women to sell their product and make money. â€Å"In advertising today, women are still dismembered—just parts of them presented to sell a product. Kilbourne says in the imposed American obsession with breasts, uplifted derrieres, etc., women forget things like the sensation they lose when they have plastic surgery on their breasts† (Kilbourne). Advertisements should make sure they do not portray women in a derogatory manner. The roles of women have dramatically changed over the generations. Women have gone from housekeepers and wives to sex symbols. Placing women on advertisements in hardly any clothing draws attention to the product itself, but making women seen vulnerable. Dolce and Gabanna, for example, uses and ad where there is one female wearing a strappy, black dress and some high heels. Dolce and Gabanna has her lying on her back, while a shirtless man is on top of her, as if he were pinning her down. There are also three shirtless men in the scene who are standing around watching. Having an advertisement, such as this one, might work to sell a product because of the impression it places on the consumer. Male viewers would presume that the only way to get a beautiful woman to be submissive is to wear products of Dolce and Gabanna. Advertisements like these make the woman in the ad provocative; therefore, viewers conceive their own opinion about women in general. See more:  The Story of an Hour Literary Analysis Essay There becomes a problem when teenagers and young adults see these women on ads dressing seductive and inviting. Women and young girls alike, start to believe they must dress in this manner because that is what the models are wearing. Women also see ads, such as the one Dolce and Gabanna have published, and they look at the women in the ad that dress tantalizing and getting handsome men, that the female viewers too, think they must dress appealing to capture a man’s attention. These advertisements are ultimately doing more damage and are corrupting our society. Advertising companies need to produce ads that make everyone look at women as beautiful, smart, and self-sufficient human beings and not a body used just to sell a product. Doing this would help society see that women can be beautiful and classy without having to be a sex symbol. It would help women get a better idea of how to be a lady. Also, the viewers of the ads would understand women are not really inferior to men, and buying a certain product does not make a person admirable. Something should be done about these advertisements. It is only putting bad ideas and morals into the consumers heads about the way they should view women. Society should appreciate women. All in all, bashing women in advertisements should be stopped and talked about by the advertising companies. Ads of this sort should not be posted all over the billboards, subways, Walters 3 televisions, and computers. Women-bashing is an ongoing problem, and it will continue to escalate if we do not open the eyes of the businesses selling the product and the viewers who agree that basing women is a sufficient way to sell a product. The ads are slowly getting out-of-control, and if we do not put our foot down now, nothing will ever be fixed, and advertising companies will continue to look for ways to make women seem less than average. Works Cited Dolce and Gabbana Boutique For Men Only 10 May 2010. Web. 21 Sept. 2010. http://www.kibitzhomme.com/?tag=dolce-gabbana. Kilbourne, Jean. Summary of Killing Us Softly 3 Welcome To Journalism Web. 1 Oct. 2010. http://hope.journ.wwu.edu/tpilgrim/j190/Stillkillussoftly3.vidsum.html. Killing Us Softly 3: Advertising’s Image of Women | Watch Free Documentary Online. Web. 19 Sept. 2010. http://topdocumentaryfilms.com/killing-us-softly-3/. 10 Worst Woman-Bashing Ads | Business Pundit. Business Pundit: Your Daily Dose of Smart Business Opinion. Web. 19 Sept. 2010. http://www.businesspundit.com/10-worst-woman-bashing-ads/.

Friday, September 20, 2019

Affect The Flight Time Of A Balsa Wood Glider Engineering Essay

Affect The Flight Time Of A Balsa Wood Glider Engineering Essay The purpose of the study was to obtain the relation between the flight time and launch height of a balsa glider of different wing area. Also the effect on flight time was recorded by changing the position of wings of the gliders. In the first part of the experiment the gliders were launched from four different height and the flight time was recorded. The experiment was conducted in a closed area in order to avoid the effect of wind. The gliders used were of different size and shape. The net acceleration acting on the gliders was also calculated by plotting a graph between square of flight time and launch height. In the second part of the experiment the wing positions for three different gliders were changed and the flight time was recorded in each of the three gliders. The launch height of the gliders was kept same. It was observed that as the launch height was increased the flight time also increased. The amount of lift could only be analysed by calculating the net acceleration in each of the gliders. The variation in the flight time due to the change in the position of wings was interpreted in terms of the increase in the loops made by the gliders i. e. the instability of the gliders or the moments of wings. Word Count- 221 Table of Contents- Introduction _______________________________________ 4 Theory _______________________________________ 5 Experimental Set up ___________________________________ 9 Method ________________________________________ 10 Result _________________________________________ 12 Conclusion _________________________________________ 22 Limitations ________________________________________ 23 Unresolved Questions _________________________________ 24 Bibliography ______________________________________ 25 Appendix ______________________________________ 26 Introduction: The question about aerodynamics has great importance in todays times and the various factors that affect aerodynamics of an aircraft or a glider is necessary in order to improve the efficiency. By taking up this experiment I have tried to analyse the acting forces on the flight of a glider such as the lift, the drag, and the weight also the theory of projectile motion plays an important role in determining the flight time of a glider. Also keeping in mind the laws of physics that relate to flight and also checking whether they are in accordance with the following experiment. Research Question- How the Wing area and position along with the launch height affect the flight time of a Balsa Wood Glider? The aim of this experiment is to study how the wing area, wing position and the launch height have an impact on the flight time of a balsa glider. In order to establish the above relations balsa gliders of different wing areas were hand launched from different heights and the flight time was recorded. As for the relation with the wing position and flight time they were hand launched as well from a fixed height with different wing positions. Theory The experiment is based on the theory of projectile motion, and fluid mechanics. Projectile Motion- When a body is projected from a certain height with a certain velocity, the acceleration on the body acts only in the downward (along y-axis) direction and the acceleration along the horizontal (x-axis) direction is zero. Since the air resistance also affects the horizontal motion of the body there might be some deceleration, however it is of a very small magnitude hence it can be neglected in the case of my experiment. The same explanation can be taken for the wind; there might be some component of the force (due to wind) which might affect the horizontal motion as well. This is also taken care of in the experiment as it is conducted in closed area. As the initial velocity is in the horizontal direction its vertical component is zero, by taking the vertical motion the flight time of the glider should depend on the height from which it has been launched and the net acceleration in the vertical direction. By varying the height in the experiment the flight time should also vary proportionately. As the height is increased the flight time should also increase. Due to the change in the forces acting on the glider the net acceleration can also change which in turn will affect the flight time. Forces There are three types of forces acting on a glider which are: Weight The weight of the body always acts in the downward direction. The weight of a body dependent on the mass of the glider and gravitational acceleration which can be taken constant for a given space. By Newtons 2nd law of motion, the weight is given by (F = mg) It  is the  force  due to the gravitational attraction of the earth on the  glider. But this force weight, which is the gravitational force, is different from the aerodynamic forces,  lift  and  drag.  The lift and the drag are mechanical forces that will act on the glider only when it is in physical contact with air which generates these forces. The gravitational force or weight is a field force; and is a non-contact force. The gravitational force (weight) between two objects depends on the masses of the two objects and the inverse of the square of the distance between these objects. The more the masses of the objects the stronger is the attraction, and closer the object are the stronger the attraction. Lift Lift is the  force  that acts on a glider upward and helps the glider to stay in the air. The lift on the glider is mainly generated by the wings.  It is an  aerodynamic  force produced by the motion of air flowing through the glider. Lift acts through the  centre of the pressure  of the glider and is in the direction which is normal to the flow of air. Lift occurs when a flow of air is  turned  by the glider. According to Newtons 3rd law of motion the flow of air is turned in one direction, and the lift is generated in the opposite direction. Since air is a  gas  and its molecules are free to move about, any solid can deflect its flow. For an  air foil, both the upper and lower surfaces plays part in turning the flow of air. There can be two types of lift static and dynamic lift. Static lift according to the Archimedes principle whenever a body is immersed in a fluid it experiences an upward force called the buoyant force. The factors on which the buoyant force depends are: The volume of the fluid displaced and; the density of the fluid. If the area of the wings increases the magnitude of the lift should also increase and the net force acting on the glider should also increases which in turn should decrease the net acceleration and hence increase the flight time. Dynamic Lift According to Bernoullis principle; the dynamic lift is due to the difference in pressure on the two sides of the body which is due to the difference in the speed of the air on the two sides of the body. There are various factors that affect lift, these are: Aircraft  wing geometry  has a large effect on the amount of lift generated. The shape and size of the wing will have a significant impact on the amount of lift generated. In order to generate lift there must be some velocity; hence if the object is moved in air then lift will be generated. Lift also depends on the  mass  of the flow.it also depends in a major way on the viscosity and compressibility of air. Viscous force or Drag Viscous force is a mechanical force. The drag, like lift, is also produce by the interaction and contact of a solid body with air. For drag to be produce, the solid body must be in contact with the air. If there is no air, there is no drag. Drag is generated by the difference in the speeds of the solid object and the air. There must be relative motion between the object and the air. If there is no relative motion, there is no drag. Viscous force always opposes the motion, hence it will be opposite to the motion of the glider. The most of the factors affecting drag is same as that affecting the lift. The viscous force can be taken as the aerodynamic friction, and one of the sources of this force is the  skin friction  between the molecules of the air and the solid surface of the glider. Since the skin friction is an interaction between a glider and the air, the magnitude of the skin friction depends on properties of both glider surface and air. The smooth, waxed surface of glider will produces less skin friction than a rough surface. And for the air, the magnitude of skin friction depends on the  viscosity  of the air. The relative magnitude of the viscous forces to the motion of the flow of air is called the  Reynolds number. Also the drag can be taken as the aerodynamic resistance to the motion of the object through the air. This source of drag depends on the shape of the glider and is called  form drag. When air flows around a body, the velocity and  pressure around the glide  are changed. The pressure is a measure of the momentum of the air molecules and a change in momentum results in a  force, a change in pressure will produce a force on the body. This component of the aerodynamic force that is opposed to the motion is the drag. Viscous force directly depends on the  mass  of the air flow going past the glider. Effect of Height on Flight time In this experiment there will be 4 heights taken but the height intervals will not be uniform in order to check the trend and see if there is a clear distinction in readings of flight time. As the height increases the flight time should increase as there is more distance to cover for the glider and since there are no forces acting as mentioned above, it is only the height that acts as a factor to change flight time. Wing area In this experiment the wing area should effect the flight time of the gliders as seen earlier, lift has a direct connection with wing area. As the lift increases the glider goes higher in the air thus increasing the flight time. Every glider has a different wing area and this makes a clear distinction between the flight times for the gliders. Wing position The wing position whether towards the front or back determines the stability of the glider while its flight. The more it is to the front of the socket it tends to do be more unstable and has a very loopy flight which increases the flight time. The further behind the wing is in the socket the more stable the glider is as the weight is more towards the centre of mass, making it more stable and also increasing the flight time however whilst a straight and balanced there are other forces acting on the flight that might pull it down to the ground. Experimental Set up Gliders In the initial stages the glider used were made by hand using a template to cut out the parts of the gliders. However these gliders lacked perfect stability and the edges had to be rubbed and smoothened in order to use make them completely aerodynamic. Even after doing so they lacked perfect specification and the material used to make them was not the right material hence they did not glide as required to. The gliders used in the later stages were bought online from amazon.com. These gliders are laser cut and ready to fly. They are made out of balsa wood. There were 3 types of gliders that were used, the parts of the gliders were precisely cut and well balanced in order to obtain a decent flight. The 3 gliders varied differently in shape, size, and weight and wing area. Area The experiment was conducted in a closed environment. The length of the place was approximately 35meters and width approximately 12meters. The wind factor was controlled as all doors and windows were shut and it was an enclosed area. Method: There were various steps that are involved in this experiment. The glider was first flown in an outdoor environment to check the flight. Since the wind factor cannot be controlled in an outdoor environment it was not possible to conduct the experiment outside as this affects the flight time. Hence an indoor area was chosen. Measuring Wing Area The gliders that will be used which each have different shape, size, and wing area. The first variable wing area cannot be measured by a given formula as it is not a uniform shape and cannot be broken into smaller shapes. The wing area will be measured by keeping the entire wing on a graph sheet whose each square area is known and the outline of the wing shape will be sketched out on the graph sheet. After having done this the number of complete squares of the known area that are enclosed by the outline of the wing will be counted. After this the number of incomplete squares and an approximation will have to be made as it is not feasible to calculate area of a fraction of the square. This will be done for each of the three gliders and will be noted down. In order to make sure that the gliders, glide properly without any hindrance and technical difficulty a test flight will be done. If there seem to be any technical problems with any of the three gliders they shall be fixed at first in order to provide accurate and legit readings. If any parts seem to be broken they will be fixed by the special adhesive which is used to stick balsa wood. Launching and Measuring Flight Time Keeping in mind that there are no holders or launching devices provided with these gliders they will have to be launched by the free hand as it is not possible to devise a launch method. This is so because making any alterations to the glider might distort its stability and will cause unequal weight balance. Although launching from the hand will have uncertainties such as different launch force and height it will be controlled as much as possible. In order to make sure the height is constant a plumb line will be taken and held from the comfortable launch height. This plumb line will then be measured in accordance with a metre scale. Every time a glider is launched it will be launched from the same height as the thread will be held at that height while launching the glider. The second height from which it will be launched will be after standing on top of a dining table. The height of the table will be measured by using another plumb line and will be measured in accordance to the metre scale. This height of the table will be added to the initial launch height and then a plumb line of that height will be held while the launch. The fourth height will be from approximately the first floor. The vast interval difference is taken so that there can be a clear trend that can be observed for the flight time. The height of the wall will be measured and then the initial height of the launch will be added to this. The fourth height will be from above a table on the first floor, in order to obtain this height the same step as the one for the table height on the lower level will be used. Taking the readings of the flight time will be done by using a stopwatch. It is not possible for me to do this alone as starting the stopwatch and launching the glider is not possible at the same time hence a little assistance will be required to measure the flight time. The assistant will start recording the flight time as soon as the glider leaves contact with my hand and will stop as soon as the glider touches the ground. These readings will then be recorded in a table. There will be 5 readings taken for each glider at each height. There are two wing positions possible either at the front of the socket or the back. Each gliders wings will be adjusted as front and back and for each position there will be 5 readings taken. Result Flight time for different launch height (Experiment1) Glider A Height (meters) Flight time ( ± 0.01s) Average( ±0.13s) t2(sec2) 1.5 1.64 1.78 1.84 1.81 1.74 3.03 2.24 2.21 2.45 2.53 2.28 2.38 5.68 5.3 3.83 3.94 4.04 3.72 3.91 15.29 6.04 4.81 4.63 4.79 4.84 4.75 22.54 As the height was increased the flight time also increased. Since the glider used was the same and the speed with which it was projected also remained same the lift experienced by the glider did not change. The increase in the time was only due to the increase in height from which the glider was projected. Glider B Height (meters) Flight time ( ± 0.01s) Average ( ±0.13s) t2(sec2) 1.5 1.25 1.5 1.28 1.3 1.32 1.75 2.24 1.54 1.68 1.61 1.59 1.61 2.60 5.3 2.19 1.94 2.4 2.33 2.24 5.02 6.04 2.78 3.01 2.92 2.84 2.87 8.26 The trend between the time of flight and the height of launch was same as in the case of glider A. Glider C Height (meters) Flight time ( ± 0.01s) Average ( ±0.04s) t2(sec2) 1.5 0.93 0.90 1.01 0.94 0.94 0.88 2.24 1.16 1.21 1.24 1.19 1.19 1.43 5.3 1.57 1.59 1.55 1.6 1.57 2.45 6.04 2.1 2.12 2.11 2.15 2.11 4.47 The trend between the time of flight and the height of launch was same as in the case of glider A and B. hence in all the 3 cases it was found that the lift experienced by the gliders did not depend upon the height of projection or the height at which the glider was flying. As seen above in the graph the flight time of the glider is directly proportional to the height from which it has been released i.e. as the height increases the time taken by the glider to touch the ground also increases. According to the equation of motion 2 If we are considering the vertical motion then the initial speed in the vertical direction will be taken as zero then 2. The three forces acting on the glider that is the weight (mg), the drag and the lift are all constant. Since the drag and the lift depend on the speed of the glider it is not changing as the speed in all the cases are constant. The above relation can be made linear by plotting a graph between t2 and h from this graph the net acceleration acting on the glider can be calculated by measuring the slope of the graph. Since: 2. Net acceleration = 2/slope of the curve. Measurement of net acceleration of the glider. Glider A Calculation Net acceleration = 2/slope of the curve. Net acceleration in glider A= = 0.51 m/s2 Glider B Calculation Net acceleration = 2/slope of the curve. Net acceleration in glider B= = 1.62 m/s2 Glider C Calculation Net acceleration = 2/slope of the curve. Net acceleration in glider B= = 3.1 m/s2 The Glider C has the maximum acceleration and Glider A has the least. This also means that Glider C comes to rest much more quickly than Glider A, Glider A also has a longer glide time and this is because of the light weight and wing span that makes it more stable while in flight. Whereas when compared to Glider C the weight is much more and the glider isnt stable enough to stay in air for a long time. The wing area also has a significant impact on this as the more wing area means more lift however when we check Glider C has more wing area but it yet doesnt get enough lift; this explains that this glider needs more thrust when launched in order to stay in air longer than the others. Wing Position (Experiment2) Glider A Wing Position for A Position Flight time ( ± 0.01s) Average ( ±0.11secs) Front 1.72 1.85 1.9 1.68 1.77 1.78 Back 1.56 1.59 1.72 1.6 1.52 1.60 As seen above when the wings of the glider are moved forward the flight time of the glider increases. Glider B Wing Position for B Position Flight time ( ± 0.01s) Average ( ±0.11secs) Front 2.13 2.06 2.24 2.17 2.26 2.17 Back 1.66 1.59 1.63 1.82 1.74 1.69 As in the case of Glider A when the wings of the glider are moved forward the flight time of the glider increases. Glider C Wing Position for C Position Flight time ( ± 0.01s) Average ( ±0.12secs) Front 1.47 1.59 1.61 1.53 1.42 1.52 Back 0.84 0.79 0.94 0.75 1.03 0.87 As in the case of Glider A and B when the wings of the glider are moved forward the flight time of the glider increases. As we can see in the graphs above the time taken for the flight when the wings are in front is more than the flight time for when the wings are pushed backward. This is because the forward wings make the flight of the glider much more unstable and cause it to loop more. The looping increases the time to touch the ground as it causes sudden immediate lift and this also increases the horizontal gliding time. Whereas on the other hand when the wings are pulled back in order to make the flight more stable but there are still other factors like weight, lift and drag that are constantly affecting the flight and causing it to descend. Conclusion: In the first part of the experiment it was found that the flight time increases as the height from where the glider was launched increases. I each of the 3 gliders the lift acting on the glider did not change as the area of the glider remained same. The change in the flight time was only due to the change in the height of the launch. The graph between the height of launch and the square of flight time gave the measure of the net acceleration in case of the 3 gliders which in turn could be interpreted in terms of net force acting on the glider. The measure of net acceleration showed that the lift produced in case of the gliders increased with the wing area. The lift in the case of Glider A was found to be maximum, as it had the maximum wing area. In the second experiment the flight time increased as the wing position was shifted towards the front of the glider. The trend obtained in all the three gliders was the same. The increase in the flight time was due to the increase in lift that made the glider shoot up and loop in the air. As the glider looped in the air the height also increased which in turn increased the flight time. The increase in the loop made by the glider was due to the instability produced by shifting the weight of the wing to the front of the plane. Limitations: There were several limitations while doing this experiment. The first and what can be considered as the most important is the launching technique. This is the most crucial part of this experiment and all the readings depend on this. Due to the fragile bodies of the glider there could be no launching technique devised that would make sure the force on each launch is the same. The lift acting on the glider depends on the speed of the glider; if the launching speed varies it can affect the lift experienced by the glider. Since it is not possible to neither control the force used for each launch nor measure it, it was the biggest drawback. When the experiment was conducted in the open the wind factor had a great impact on the flight of the gliders. The gliders being light and very fragile, the wind outdoor was drifting the gliders into different directions and also slowing them down. This change in path and time was random and unpredictable. Since it was not possible to control the wind the experiment was carried out in a closed environment, yet there was some wind that affected the flight and caused slight deviation in path which could have possibly increased the flight time or even decreased it. Since the gliders were launched several times and had not landing mechanism as well, the rough landing chipped quite a few parts of the gliders that made the flight for the later readings relatively unstable and defective. Unresolved Questions: The effect of projection velocity on the flight time was not clear as the gliders were launched with almost same velocity and force. The speed with which the glider moves effects both the lift on the glider and the drag acting on it. The two forces are very important in deciding the flight of the gliders. By designing a proper launch mechanism the effect of speed or the launch force would had been studied. Also the efficiency of the flight could have been studied by measuring glide ratio i.e. the ratio of the horizontal distance travelled and the loss of height travelled in a given time. Bibliography Books: Giancoli, Douglas C., Physics Principles with Applications, 6th Edition, Pearson Education Limited, NJISBN: 0-13 -184661-2-1. Nelkon, M., and Parker, P., Advanced level Physics, London, Heinemann Educational Books Limited, ISBN 0-435-68636-4 Tsokos, K., A., Physics for the IB Diploma,5th Edition, Cambridge University Press, ISBN 978-0-521-13821-5 Websites: http://en.wikipedia.org/wiki/Gliding_flight http://www.grc.nasa.gov/WWW/k-12/airplane/glider.html http://www.skysailing.com/pages/theory.htm http://web.mit.edu/16.00/www/aec/flight.html

Biosensors or enzyme electrodes

Biosensors or compound cathodes Presentation OF BIOSENSORS:- Biosensors or compound cathodes perpetually allude to such gadgets that s...